Switchboards

GE Switchboards
Industrial Systems – Distribution

Merchandised and Metering Switchboards— Jiffy II Spectra
EUSERC West Coast Utility Applications

The GE Jiffy II Service Entrance Switchboard is designed especially to address the requirements of your small project needs. The compact unit combines the electrical distribution panel, the main service disconnect and the utility metering compartment into one spacesaving unit, delivering maximum installation opportunities.

EUSERC West Coast Utility Applications The GE Jiffy II Service Entrance Switchboard is designed especially to address the requirements of your small project needs. The compact unit combines the electrical distribution panel, the main service disconnect and the utility metering compartment into one spacesaving unit, delivering maximum installation opportunities.

Canadian Jiffy III Switchboards

The GE Jiffy III Utility Service Entrance Switchboard is designed especially to address the Canadian market. The compact unit combines the electrical distribution panel, the main service disconnect and the utility metering compartment into one space-saving unit, delivering maximum installation opportunities.

The GE switchboard is floor mounted and rated up to a maximum 1200A, 42 kAIC @600V. At 15” (381 mm) deep, the electrical distribution board easily fits into the tightest areas where space is typically limited. The Jiffy III is UL and cUL1 approved and meets the seismic requirements of IBC Zone 4 and CBC Zone 4.

Designed and approved specifically for the Canadian Utility Market2, the Jiffy III is available with mains rated at 800A, 1000A and 1200A; 80% and 100% rated (with the exception of 1200A, which is 80% rated only); and with or without Ground Fault protection. A full line of field installable Digital Solid State Electronic Trip Molded-Case Breakers is also available. With a combination of superior features and options, the GE Jiffy III Utility Service Entrance Switchboard not only meets your space-saving needs, but also offers total flexibility in design to meet the requirements of the project.

Commercial Metering Switchboards
EUSERC West Coast Utility Applications
NON–EUSERC Utility Applications
Lever Bypass

GE Commercial Metering Switchboards are designed specifically to serve the EUSERC market in the western United States. In addition, they serve the NON-EUSERC markets with a Lever By-Pass arrangement. They are UL listed and labeled and offer a wide range of installation and performance features that simplify any project.

Metering sections are assembled with two sockets pre-wired on the line and load sides. All sockets are 200A continuous duty. A full selection of tenant mains are available including circuit breakers, fusible switches and T-Fuse pullouts.

Spectra Retail Integrated Switchboard Solutions

Spectra Retail Integrated Switchboard solutions save time, money and space, yet sacrifice nothing in terms of safety, performance or flexibility. You get flexibility in design and consistency in execution. Units expand or contract to accommodate your specific needs. And not only do they reflect GE’s rigorous Six Sigma quality standards, they are also built and tested in accordance with NEMA PB-2, UL 891 and the NEC. All sections and devices are UL listed and UL labeled.

Spectra Series and Class 5 Utility
Utility Metering Compartments

Compartments are available with the following features:

  • CT busbars mounted on high impact glass fiber polyester insulation and arranged in an edgewise plane.
  • Door with concealed hinges, 3-point catch and lock, handle seal over CT compartment: barriers rear and bottom (top).
    Note: The bottom barrier is furnished at top if main device is over CT compartment.
  • 9” or 11” centerline standard. For other centerlines refer to factory.
  • CT bus bars drilled for transformers with NEMA terminations.
  • #10-32 and 1/4-20 screws for potential taps.
  • Removable links provided if part of utility requirements.
  • Type 1 — Compartments have 9” centerlines
  • Type 2 — Compartments meet EUSERC standards
  • Type 3 — Compartments have 11” centerlines, potential transformer space and mounting bracket if required.
  • Cold sequence metering has CT compartment on load side of main device. Hot sequence CT Compartment is on line side.

For more information on GE Switchboards, please e-mail our sales dept at sales@jostfewkes.com or utilize our Quotation Request Form.

top